How do you change back drum brakes?

How do you change back drum brakes?

Part 1 of 4: Prepare the vehicle

1. Materials Needed.
2. Step 1: Loosen the lug nuts of the vehicle.
3. Step 2: Secure the vehicle on jack stands.
4. Step 2: Remove the brake drum.
5. Step 3: Clean the drum brake assembly.
6. Step 4: Inspect the brakes.
7. Step 5: Disassemble the brake drum assembly.
8. Step 6: Remove the brake drum shoes.

How do you remove rear brake pads?

Steps for changing your brake pads

1. Remove the wheel.
2. Remove the slider bolt.
3. Pivot the caliper up.
4. Slide out the old brake pads.
5. Replace the retaining clips.
6. Slide in the new brake pads.
7. Retract the pistons.
8. Monitor the brake fluid level.

How do you remove a drum brake assembly?

Unscrew the brake drum if needed.

1. Use a screwdriver to remove the screws securing the brake drum to the wheel.
2. Draw the brake drum forcefully towards you.
3. Use a screwdriver and rubber mallet or a brake drum puller to take the drum off of the wheel if you are unable to remove the drum by unscrewing it and pulling it.

Do drum brakes need to be adjusted?

Drum brakes need to be adjusted from time to time to make sure they function properly throughout their lifespan. Improperly adjusted brakes can either accelerate shoe and drum wear or cause the pedal to go to the floor before the brakes engage. In extreme cases it can cause the rear wheel(s) to lock up.

How do you know when drum brakes need replacing?

Technical Bulletins

1. Inconsistent brake pedal feel. If the rear brakes are drum brakes, the driver may feel vibrations under braking.
2. Hand brake feels loose. If the hand brake requires a hard yank to keep the car from rolling off, chances are the brake shoes need replacing.
3. Scraping noise while braking.

What do rear brake shoes do?

Brake shoes stop the car by pushing outward, while brake pads stop it by moving closer together. Instead of sitting inside a brake drum, brake pads are positioned around a disc called a rotor.

How much does it cost to replace rear brake shoes?

Brake Shoes Replacement Cost – RepairPal Estimate. The average cost for brake shoes replacement is between $247 and $280. Labor costs are estimated between $124 and $156 while parts are priced at $123. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

How long does it take to change rear brake pads?

And how long does brake pad replacement take?” Because the various components that make up the brake system are a normal wear item, they will eventually need to be replaced and It generally takes 30 minutes to 1 hour as per expert mechanics.

How much does it cost to change rear brake pads?

The average brake pad replacement costs around $150 per axle, but these costs can rise to around $300 per axle depending on your vehicle’s brake pad materials. The least expensive brake pads use organic material.

How do I know if my rear drum brakes need to be adjusted?

Periodic adjustment of the drum brakes makes sure that the brakes do not drag when driving as this can rob power from the vehicle and cause the brakes to wear out much more quickly. Drum brakes usually need to be adjusted when the brake pedal has to be pressed down a lot before the brakes engage.

Can you change the brakes on a Pontiac Sunfire?

The rear wheel brakes on a Pontiac Sunfire, like those on other cars, will wear much faster than the brakes in the front. When you change the rear brakes, you need to do both wheels at the same time regardless of the wear that is present. Changing the rear brakes is not hard, but you must do it properly or they won’t perform as they should.

How do you replace the brake drum on a SunFire?

Remove the wheel and the brake drum. If the drum is difficult to take off, hit it several times with a rubber mallet until it breaks free. Use pliers to remove the round locking springs. Grip the top of the spring with the pliers, push the spring down, and twist it until it comes free.

How can I adjust the width of my brake shoes?

Install the actuator pivot, lever and return spring, and then lift the actuator lever up and hook it to the lever. Measure the width of the inside of the drum and then measure the width of the brake shoes. Adjust them as needed by spinning the star screw on the adjuster until they reach the proper width.

The rear wheel brakes on a Pontiac Sunfire, like those on other cars, will wear much faster than the brakes in the front. When you change the rear brakes, you need to do both wheels at the same time regardless of the wear that is present. Changing the rear brakes is not hard, but you must do it properly or they won’t perform as they should.

Remove the wheel and the brake drum. If the drum is difficult to take off, hit it several times with a rubber mallet until it breaks free. Use pliers to remove the round locking springs. Grip the top of the spring with the pliers, push the spring down, and twist it until it comes free.

How do you change the brake shoes on a car?

You can then use a ratchet to remove the axle bearing nut and pull off the brake drum. Then, pull off the brake shoe springs, clips, and cable so you can pull off the old brake shoes. Slide the new brake shoes into place and reconnect all of the springs, clips, and cables so you can replace the drum and axle.

How do you change the brake Springs on a car?

Reconnect the brake springs you disconnected in order to remove the old brakes. Use a pair of pliers to ensure you don’t pinch or injure yourself in the process. If the springs become too bent or damaged in the process, they will have to be replaced. Be careful not to overstretch the ends of the spring.