How do you tie an existing roof

To tie into the side of an existing roof, put a new roof truss on the walls of the addition, brace it upright, then snap chalk lines on the shingles to mark the center line of the new roof valleys, where old and new roofs will connect.

How do you tie a new roof to an old roof?

The easiest way to tie in the new shingles with the old is with a cut valley (see Four Ways to Shingle a Valley). After the addition roof is framed and sheathed, snap a line on the existing roof shingles 2 in. up from the valley center, and cut through the shingles and underlayment.

Can you screw into roof trusses?

It is possible to screw into your truss, but it’s risky. … However, only screw into your truss if it’s absolutely necessary, and consult the engineer who designed your attic before you do. You can remove a screw, but its mark will be there forever.

How do you join two roofs together?

1. Step 1 – Preparing the Area. …
2. Step 2 – Measuring the Length of the Joined Area. …
3. Step 3 – Prepare a Piece of Flashing Material. …
4. Step 4 – Place the Flashing on the Meeting Point. …
5. Step 5 – Sealing the Edges of The Roof with Lumber. …
6. Step 6 – Apply a Bead of the Sealant Material.

How do you join different roof pitches?

Position the flashing between the two roof pitches. Slide the right edge of the flashing under the highest roof pitch. Place the 2-by-4-inch piece of lumber along the center of the flashing. Gently bend the flashing using the edge of the lumber until both sides of the flashing match the slope of the two roof pitches.

Can you drill holes in roof rafters?

A truss cannot be drilled without authorization of a licensed professional engineer or the truss manufacturer. ”Truss members shall not be cut, notched, drilled, spliced or otherwise altered in any way without the approval of a registered design professional,” according to the International Residential Code (IRC R802.

What is it called where the wall meets the roof?

A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.

Do I need truss clips?

In such situation, framing anchors or truss clips should be used. It is strongly recommended that for trussed after roofs the truss clip is used, whether or not it is specified on the drawing. … All metalwork used in roof construction should be galvanised, including nails to prevent corrosion.

Are truss clips required?

Install slot nails in the middle of the slot. Products not intended for floor applications due to the frequency of floor joist deflections and potential for squeaks. 1. … Clips are required on both sides of the truss to achieve F1 loads in both directions (stagger parts to avoid nail interferences).

Where do two roofs meet?

Roof Ridge: The roof ridge, or ridge of a roof is the horizontal line running the length of the roof where the two roof planes meet. This intersection creates the highest point on a roof, sometimes referred to as the peak.

Article first time published on

What is a combination roof?

A combination roof is exactly that – a combination of different types of roofs and design features. For instance, a home could have a gabled roof with a skillion over the porch, or a hip roof with a gabled front porch, or a gabled roof with a domed cupola – or any combination of styles.

What is the trim around a roof called?

Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.

What is roof edging called?

The eaves The eaves are the edges of the roof which overhang a vertical external wall and, normally, they jut out over the side of a building creating an overhang, so rainwater stays clear of the walls.

What is the edging around the ceiling called?

This molding is the “crowning” architectural feature of a room, as it decorates the transition between walls and the ceiling. Crown moldings, also known as cornice moldings, typically boast intricate silhouettes—although many types of crown molding exist. Related: 10 Ways to Reinvent Any Room with Crown Molding.

Can you add a roof to an existing deck?

Can I put a roof over my deck? In most cases, yes! If you’re looking to add a roof to your deck, you can do this by installing additional supports. Unless you have construction experience, it’s best to hire professionals to do this for you.

How do you cover a concrete patio?

1. Fake A Concrete Patio Cover Up With Stain. …
2. How to Cover Your Patio with Paint and Make It look Like Tile. …
3. Use Pavers to Cover Your Concrete Patio. …
4. Use Tile To Cover a Concrete Patio. …
5. Concrete Patio Idea – Cover Up with a Deck! …
6. Another Concrete Patio Cover Up Using Stain.

How do you redo a porch roof?

1. Remove any damaged shingles or felt paper. Many times when a porch roof is damaged, you will need to remove the damaged portions.
2. Mark the damaged area and cut it out. …
3. Cut a piece of plywood that is the same as the area that you cut out. …
4. Cover the patch with felt paper. …
5. Replace the shingles.

How do you jack up a sagging porch?

1. Place one high-lift jack under the horizontal support beam on both sides of the lowest point of the sagging porch line. …
2. Pump both handles equally until the sag on the horizontal beam is reversed, and is actually inverted upward, 1-inch higher than needed.