What is the standard size of a clawfoot tub

Clawfoot tub lengths range from a compact 54” to an oversized 72”, with 59” lengths most commonly purchased; widths range from 30” to 40” or more, with 32” widths especially popular (choose a wide tub if you plan on bathing a deux); and depths range from 24” to 30” or more.

Are clawfoot tubs bigger than regular tubs?

Clawfoot tubs are almost always larger in almost every dimension than a standard built in tub – the feet make them taller, and in addition to being long and deep (after all, they are meant for soaking), you also want to leave a little “elbow room” around the tub.

Can you put a clawfoot tub in a small bathroom?

They also come in a variety of sizes, so even you have a small bathroom, there is likely a clawfoot tub that will work for your space. … Small bathroom? No problem! A clawfoot tub actually takes up less space than a traditional installed tub, allowing you to add a relaxing soaker to rooms where you didn’t think possible.

How is a claw foot bath tub measured?

Many claw foot and stand-alone tubs are rounded or peaked in the center of the tub on each side, so be sure to stand in the tub itself and measure the distance from the peak on one end to the peak on the other. Measure to the outside lip of the tub to make sure you get the most accurate measurement.

Why are clawfoot tubs bad?

“It doesn’t butt up against the wall, so you get a lot of spillage and it can cause damage to your wall or can seep in and actually drip down from your bathroom to your lower level ceiling,” Jonathan Scott of HGTV’s Property Brothers, told PopSugar. … Consider tiling bathroom walls or nixing a clawfoot tub altogether.

What size shower curtain do you need for a clawfoot tub?

Typically, a curtain that’s designed for a clawfoot tub will measure about 180 inches wide by 70 inches long. One of the biggest complaints people have about showers in a clawfoot tub is that the curtain billows inward and sticks to them while they’re showering.

How far should a clawfoot tub be from the wall?

The Magic Number: 6 Inches As a rule of thumb, the minimum end-to-end (length) additional space you’ll need for a clawfoot, pedestal, or freestanding tub is 6 inches. Any less and the tub will look cramped in the space.

What are the dimensions of a cast iron tub?

The most common sizes for cast iron bathtubs would be 66 inches and 72 inches. Of course if you want something smaller, they can go down to 60 inches if you have a smaller space. The reason for the popularity of these sizes is due to their incredible versatility.

What size is a standard tub?

The most common bathtub installation is an alcove bath with an overall size of 60 inches x 32 inches. Standard tubs usually have external measurements around 60 inches long, 30 inches wide and 14 to 16 inches high.

How wide is a cast iron tub?

While a standard cast iron tub might be 68” by 30”, this is a measure of the exterior length and width. The interior width for this bathtub could easily narrow to only 18”- 20” if measuring across the bottom of the bathtub.

Article first time published on

How much do cast iron tubs weigh?

Depending on its size, an iron tub can easily weigh 350-500 pounds or more when empty.

How much is a clawfoot bathtub worth?

The average all-in cost of a vintage clawfoot tub is $2,850. This includes the tub, refinishing, hardware and installation. Likewise, the all-in average cost for an acrylic clawfoot is $2,250.

What can I do with an old clawfoot tub?

1. Turn it into a planter in your garden. …
2. Transform it into an outdoor sofa. …
3. Transform it into a chaise lounge. …
4. Turn it into a couch. …
5. Upcycle it into a chair. …
6. Transform it into a coffee table and planter.

Will a clawfoot tub crack tile?

Will a clawfoot tub crack tile? Tile floors, especially porcelain, are very durable and will not break under heavy weight but they can scratch. Tile flooring is ideal for supporting a heavy bathtub at full capacity.

Does a clawfoot tub add value to a home?

According to the RealEstate.com survey, starter homes with claw-foot tubs sold for nearly 30% more than expected. Coffered ceilings also helped homes sell for 30% more than expected, and farmhouse sinks (thanks Joanna Gaines) helped homes sell for 26% more than expected.

Are clawfoot tub feet interchangeable?

Feet are not interchangeable. A tub for two would work best with a double ended clawfoot tub, while a single slipper clawfoot tub is only for one person. A double ended slipper clawfoot tub may accommodate two if the tub is long and wide enough.

How much room do you need around a clawfoot tub?

How big is a clawfoot tub? Typically, a clawfoot tub is generously sized. Ensure that the tub you want will fit through all doors, halls, and stairwells to get into the bathroom, and allow for at least 3-6 inches of space on each side of the tub.

How big is a 2 person bathtub?

Common freestanding bathtub sizes for 2 people A medium sized two person bathtub starts at around 66.9 inches long with a width of 33.5 inches and a height of 22 inches. The largest of the medium sized bathtubs comes in at 70 inches with a width of 35.4 inches and a height of 22.5 inches.

How big should a freestanding tub be?

Common or standard dimensions for a freestanding bathtub are 60 inches long (5ft), 30 inches wide (2.5ft) with 19 inches of water depth (1.89ft). Small freestanding bathtubs can run 55 inches long(4.58ft), 27 inches wide (2.25ft) with a water depth of 15(1.25ft).

How do you measure a curtain for a clawfoot tub?

Add the length of the curtain plus another 2 inches. Then measure the distance from the floor to the ceiling and subtract the first number from it. For example, if the ceiling height is 96 inches and the shower curtain is 72 inches long, subtract 74 (72 + 2) from 96 to arrive at 22 inches.

What is the standard shower curtain size?

Across the board you’ll find three options when it comes to standard shower curtain sizes: 70 x 70 inches. 70 x 72 inches. 72 x 72 inches.

What are the different sizes of bathtubs?

60 inches long (5ft) 30 inches wide (2.5ft) with 16 (1.3ft) inches of water depth. Smaller sizes typically run 45 inches long (3.75 ft), 30 inches wide (2.5ft) with 14 inches of water depth (1.16 ft). Large size you are looking at 72 inches long (6ft), 42 inches wide (3.5ft) and 20 inches of water depth (1.6ft).

How do I know what kind of tub I have?

1. Step 1 – Press on the Side of the Bathtub. If you press on the side of your bathtub and it has a little give, chances are it is made of acrylic of fiberglass. …
2. Step 2 – Inspect Surface Damage. …
3. Step 3 – Hold a Magnet to the Tub. …
4. Step 4 – Look for Extra Supports.

Can I replace a 30 inch tub with 32?

The bigger issue is when the width of the new tub exceeds the old space. Replacing a 30-inch tub with a 32-inch tub is an example. If the floor is concrete, this makes adjusting the flooring more difficult.

How many gallons does a clawfoot tub hold?

Clawfoot tubs can hold between 40 to 60 gallons of water.

What does a cast iron tub look like?

A cast iron tub will sound like a deep gong, just as if you hit a cast iron frying pan. Look at the bottom of the tub if possible. A cast iron tub will be black, and a steel tub will be metallic, although it may be covered with a layer of paint. An acrylic tub will look like coated plastic.

Is it worth saving a cast iron tub?

if it’s in good condition, keep it. cast iron tubs are wonderful, and hold up better than the acrylic tubs that you can get now. they hold heat better too, if you want to soak.

Can my floor support a cast iron tub?

In general, unless there is something wrong with the joist spacing or the wood has rotted, the framing in most houses should be able to support a standard size cast iron tub with no problem.

How long does a cast iron tub last?

Miracle Method, like many refinishing companies, offers a five-year warranty. But says Diane Robbins, co-owner of the franchise that resurfaced Jackie’s tub, with proper care and maintenance (nonabrasive and bleach-free cleaners only), a refinished cast-iron tub surface should last 15 to 20 years.

How do I know if I have a cast iron tub?

1) Remove the overflow cover and popup lever from the head end of the tub and look at the edge of the hole. You should see black cast iron or bright steel. Also, if you remove the overflow cover, the material between it and the plumbing will be about 1/4 ” thick if it is cast iron.

Can you break a cast iron tub with a sledgehammer?

I wouldn’t even think of using a sledgehammer on a cast iron tub or sink without taking the right safety precautions. Once you have yourself protected and ready for work, simply strike covered areas of the tub with the sledgehammer, paying attention to how much force you actually need to break pieces off.